N 6661 is a bi-pass floor guide that can be used universally on most wardrobe doors systems. The nylon guides are adjustable to accommodate 3/4 to 1-3/8 in closet doors. The carpet riser shim plates can raise the guides from 1/8 to 5/8 in above the floor to accommodate the height of the carpet.

N 6706 is a bottom mount pivot used by many bi-fold door manufacturers. The 3/8 in Dia nylon base houses a 1/4 in pivot with a hex head nut for adjustment.

Plated steel, universal design fits a 3/4 in Dia hole.

Held in place by two nails used by many wardrobe & door manufacturers. Includes two pull handles, four brass nails for installation. 7/16 in depth. Used by many wardrobe manufacturers.

N 6567 is a set of two white nylon floor guides for a single door that is any thickness. Often used on pocket doors as well as bi-pass door systems. Used by several door manufacturers.

This is a 2 in round door pull that comes with nails to hold it in a 2 in Dia hole in the closet door. It is plated brass and used on a variety of Closet Door manufacturer's doors. There are two pulls and four nails per package.

N 6562 is a three-piece adjustable floor guide. Made of white nylon, the guides at each end can be adjusted inward to accommodate doors 3/4 to 1-3/8 in THK. Used by many closet door manufacturers. The guides extend 3/4 in from the floor. For taller guides see N 6760 or N 6761.

This is a single wheel, top hung, side mounted adjustable roller bracket with a 1 in convex nylon roller that fits onto the back wardrobe door panel. The stamped steel adjustable bracket has a 3/4 in offset and fits onto a 3/4 to 1-3/8 in THK door. Primarily used on Cox door systems, it may also be found on a variety of other wardrobe door manufacturer's doors. For deeper offsets see Prime-Line parts N 6514 and N 6515.

Fits Acme wardrobe doors in top hung side-mounting applications. Adjustable steel bracket with 1/4 in W round edge nylon wheel. For 3/4 to 1-3/8 in THK doors. Includes six #8 x 3/4 in Phillips pan head screws. N 7030 and N 7031 have nickel steel brackets.

Fits Cox wardrobe doors in top hung side-mounting applications. Steel offset adjustable bracket with 1/4 in W round edge nylon wheel. For 3/4 to 1-3/8 in THK by-passing doors up to 50 lb. Includes 2 #8 x 3/4 in Phillips pan head screws.

Held in place by two nails used by many wardrobe & door manufacturers. Includes two pull handles, four brass nails for installation. 7/16 in depth. Used by many wardrobe manufacturers.

This is a single wheel, top hung, side mounted adjustable roller bracket with a 1 in convex nylon roller that fits onto the front wardrobe door panel. The stamped steel adjustable bracket has a 1/4 in offset and fits onto a 3/4 to 1-3/8 in THK door. Primarily used on Cox door systems, it may also be found on a variety of other wardrobe door manufacturer's doors.

Fits Acme wardrobe doors in top hung side-mounting applications. Adjustable steel bracket with 1/4 in W round edge nylon wheel. For 3/4 to 1-3/8 in THK doors. Includes six #8 x 3/4 in Phillips pan head screws. N 7030 and N 7031 have nickel steel brackets.

Restore smooth, reliable operation to your sliding closet doors with this top-mounted tandem roller assembly. Designed for use with Harvey and similar closet door systems, this center-mount roller features dual 3/4 in convex nylon wheels that provide balanced support and consistent glide. Ideal for doors between 3/4 in and 1-3/8 in THK, this assembly helps reduce sticking, misalignment and uneven movement for improved door performance. The rollers are housed in a durable stamped steel casing and mounted on a 5/16 in threaded steel rod, allowing for height adjustment and precise alignment during installation. This adjustable design ensures a proper fit and smooth track engagement, making it a great solution for repairs or replacements. The top-hung configuration threads into a compatible bracket, such as Prime-Line part N 6797, for secure installation. Mounting hardware is included and set-up requires only a standard Phillips head screwdriver. Built for durability and ease of use, this tandem roller assembly is a dependable choice for maintaining or upgrading closet door systems. Always verify dimensions and compatibility before purchasing.

N 6761 is a three-piece adjustable floor guide. Made of white nylon, the 1-1/4 in tall guides at each end can be adjusted inward to accommodate doors 3/4 to 1-3/8 in THK. Used by many closet door manufacturers.

N 6560 is a two-piece adjustable floor guide. Made of white nylon, the guides can be adjusted to accommodate doors 3/4 to 1-3/8 in THK by using the slots in the stamped steel floor base. Used by many closet door manufacturers. The guides extend 5/8 in from the floor.

N 6563 is a white nylon floor guide for 1-3/8 in THK doors. A universal design. At 1-1/8 in tall, it provides a taller than normal guide for most standard thickness closet doors.

Fits Cox wardrobe doors in top hung side-mounting applications. Steel offset adjustable bracket with 1/4 in W round edge nylon wheel. For 3/4 to 1-3/8 in THK by-passing doors up to 50 lb. Includes 2 #8 x 3/4 in Phillips pan head screws.

Fits wardrobe doors in top hung side-mounting applications. Offset adjustable steel bracket with 1/4 in W round edge nylon ball bearing wheel. For 3/4 to 1-3/8 in THK doors. Includes 2 #6 x 5/8 in and 1 #4 x 3/4 in Phillips pan head screws.

These sliding panel door finger pulls are constructed of stamped steel and they come finished in a satin nickel plating. They feature a 5/16 in deep-recessed area and fit into 3/4 in Dia holes. These finger pulls are used on by-passing sliding Closet Doors, medicine cabinets and other furnishings and they are used by a variety of sliding door manufacturers.

Fits wardrobe doors in top hung side-mounting applications. Offset adjustable steel bracket with 1/4 in W round edge nylon ball bearing wheel. For 3/4 to 1-3/8 in THK doors. Includes 2 #6 x 5/8 in and 1 #4 x 3/4 in Phillips pan head screws.

N 6840 is an adjustable top hung, side mounted bracket with a 1/16 in offset and 7/8 in flat nylon roller used on the front sliding door panel. It fits 3/4 to 1-3/8 in thick doors.

This tandem roller assembly is constructed from nylon. It features an adjustable top-mount design with round edge nylon wheels with a 1/2 in nut. It fits Acme and other similar styled doors that are 3/4 to 1-3/4 in THK.

This is an adjustable top hung, side mounted bracket with a 3/8 in offset and 7/8 in flat nylon roller used on-the back of a sliding door panel. It fits 3/4 to 1-3/8 in THK doors. Used by a variety of sliding closet or wardrobe doors.

This is a side mounted, top hung wardrobe roller assembly with a single 7/8 in convex nylon wheel for the back sliding door. The stamped steel bracket assembly is adjustable and has an 1/2 in offset. It is fitted onto the wardrobe front door and fits 3/4 in to 1-3/8 in THK doors. Used by Cox door systems as well as a variety of other wardrobe door manufacturers. For the back wardrobe door see Prime-Line part N 6505.

This is a 2-1/8 in round flush-mount door pull held in place with the provided nails. It has a classic bronze finish and used on many Closet Door manufacturer's doors. There are 2 pulls and 4 nails per package.

Use this mirror door roller assembly to replace old or broken parts on your steel-framed sliding mirror doors and keep your doors operating ideally. It features snap-in bracket clips which are designed to lock into steel-framed door rails to hold the Doorrs together and it is made of a steel housing and a flat edge plastic wheel. It is strong, durable and built to last, plus the durable plastic wheel provides a smooth, long-lasting and quiet roll. This mirror door roller assembly has a 1-7/16 in OD wheel in a housing that measures 3-1/16 in W x 3-3/8 in H. Installation of this roller assembly is quick and easy. This assembly mounts into the lower corners of sliding mirrored closet doors. It is adjustable once installed and it is used by many Closet Doorr manufacturers.

Single wheel; adjustable steel bracket; also acts as corner bracket for steel frame by-passing door; fits on Acme. Contents: 2 roller assemblies.